Guten Morgen...so mehr als 10 Stunden mit de Problem befasst, weiter gehts
Hier vielleicht ein Fehler zu entdecken? $scgi_port = 5005; $scgi_host = "127.0.0.1"; Path: /var/www/rutorrent/conf/users/xxxxxxxxx.config.php
Code:
# Maximum and minimum number of peers to connect to per torrent.
min_peers = 5
max_peers = 20
# Same as above but for seeding completed torrents (-1 = same as downloading)
min_peers_seed = 5
max_peers_seed = 20
# Maximum number of simultanious uploads per torrent.
max_uploads = 5
# Global upload and download rate in KiB. "0" for unlimited.
upload_rate = 50000
download_rate = 50000
# Default directory to save the downloaded torrents.
directory = /var/www/rutorrent/share/users/MEINNAME/torrents
# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /root/_PATH_LIBS/rtorrent-0.8.6/users/MEINNAME/session
# Watch a directory for new torrents, and stop those that have been
# deleted.
schedule = watch_directory,5,5,load_start=/var/www/rutorrent/share/users/MEINNAME/torrents/*.torrent
schedule = untied_directory,5,5,close_untied=/var/www/rutorrent/share/users/MEINNAME/torrents/*.torrent
schedule = tied_directory,5,5,start_tied=/var/www/rutorrent/share/users/MEINNAME/torrents/*.torrent
#on_finished = move_complete,"execute=mv,-u,$d.get_base_path=/var/www/rutorrent/share/users/MEINNAME/torrents/ ;d.set_directory=/var/www/rutorrent/share/users/MEINNAME/torrents/"
on_start = link1,"create_link=tied,,.started"
on_stop = link1,"delete_link=tied,,.started"
on_finished = link1,"create_link=tied,,.finished"
on_erase = link1,"delete_link=tied,,.finished"
# SCGI
scgi_port = localhost:5005
umask = 000
# Close torrents when diskspace is low.
schedule = low_diskspace,5,60,close_low_diskspace=100M
# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
schedule = ratio,30,30,"stop_on_ratio=500"
# The ip address reported to the tracker.
ip = (habe ich meine Server IP eingefügt)
# The ip address the listening socket and outgoing connections is
# bound to.
bind = XXX.XXX.XXX.XXX
# Port range to use for listening.
port_range = 50001-50001
# Start opening ports at a random position within the port range.
port_random = no
# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
check_hash = yes
# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = no
# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=XXX.XXX.XXX.XXX
#schedule = bind_tick,0,1800,bind=XXX.XXX.XXX.XXX
# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext
encryption = allow_incoming,try_outgoing,enable_retry
# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
dht = disable
# UDP port to use for DHT.
#dht_port = 49300
# Enable peer exchange (for torrents not marked private)
peer_exchange = yes
#
# Do not modify the following parameters unless you know what you're doing.
#
# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10
# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100
# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10
#http_capath=/etc/ssl/certs
_PATH_LIBS ist wirklich ein Verzeichnnis bei mir...nicht wundern...
Ist da ein fehler zu sehen?